Max Systems LabelMax XS Instrukcja Obsługi Pobierz pdf (Strona 19)

Page 1-15 SATO D508/D512 Service Manual

OFFSETS

There are two offset settings stored in the printer; one for the Cut mode and one for the Tear-Off

mode.

These two offsets can be set independently and will remain in the printer until a new command is

received changing the setting or until power is turned off.

The default settings can be determined by printing a User Test Label.

The following should be used as starting points for establishing the three Offset values:

Mode Length of Offset (mm) Length of Offset (in) Print head resolution

CUTTER 17.9 0.70 143/215

TEAR-OFF 29.2 1.15 234/350

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 89 90

SERVICE MANUAL 1
SATO America, Inc 2
Table of Contents 3
Replacement Procedures 4
Checks/Adjustment Procedures 4
OVERVIEW 5
UNPACKING 8
PRINTER PART NAMES 9
SETTING UP THE PRINTER 10
LOADING MEDIA 11
Unit 1: Overview 12
LABEL SENSING 13
CONFIGURATION 14
3.1 OPERATING PANEL 14
CONFIGURATION: THE REAR PANEL 15
Configuration Switch 16
THE CONFIGURATION PANEL 16
DIP SWITCH SETTINGS (CONT’D) 17
Configuration Switch 17
CUTTER 17.9 0.70 143/215 19
TEAR-OFF 29.2 1.15 234/350 19
POTENTIOMETER ADJUSTMENTS 20
DATA DUMP DIAGNOSTIC LABEL 22
PRINTING TEST LABELS 23
BASIC AND INTERFACE 25
SPECIFICATIONS 25
Attribute 26
Attributes 27
Barcodes 28
Physical Attributes 28
Optional Accessories 29
INTERFACE SPECIFICATIONS 30
THE RECEIVE BUFFER 31
THE RECEIVE BUFFER (CONT’D) 32
IEEE1284 PARALLEL INTERFACE 33
RS-232C INTERFACE 34
RS-232C INTERFACE SIGNALS 35
READY/BUSY FLOW CONTROL 36
X-ON/X-OFF FLOW CONTROL 36
LOCAL AREA NETWORK INTERFACE 37
WIRELESS 802.11 LAN INTERFACE 37
TROUBLESHOOTING 39
TROUBLESHOOTING TABLE 41
MEANDERING MEDIA 42
PRINTER CREATES A BLANK LABEL 42
INCORRECT LABEL POSITIONING 42
NO PRINTED IMAGE 42
PARALLEL INTERFACE 43
RS-232 SERIAL INTERFACE 43
LAN ETHERNET INTERFACE 44
WIRELESS LAN INTERFACE 44
TROUBLESHOOTING FLOWCHARTS 45
See Pg 4-3 46
Unit 3: Troubleshooting 47
See Pg 1-13 48
See Pg 4-5 48
See Pg 4-13 48
PROBLEM: PRINTING IS TOO DARK 50
See Pg 4-3 52
See Pg 4-2 52
See Pg 4-17 54
See Pg 1-13 54
to 1-15 54
TEST PRINT TROUBLESHOOTING 55
TEST LABELS 55
Figure 3-2, Sample Test Label 56
REPLACEMENT 61
PROCEDURES 61
REPLACEMENT PROCEDURES 62
PLATEN ROLLER REPLACEMENT 63
ACCESSING THE MAIN BOARD 63
Screw x4 64
FUSE REPLACEMENT 65
PANEL BOARD REPLACEMENT 67
LABEL SENSOR REPLACEMENT 70
COVER SENSOR REPLACEMENT 72
DRIVE MOTOR REPLACEMENT 74
DRIVE GEAR REPLACEMENT 76
CUTTER ASSEMBLY 78
1CHECKS/ADJUSTMENT 81
ADJUSTMENT PROCEDURES 82
FACTORY CLEAR 83
PRINT DARKNESS 84
Figure 5-2, Test Module Usage 85
PRINTER COUNTER CLEAR 86
TEST PRINT COUNTER CLEAR 87
Unit 5: Adjustment Procedures 88
GAP SENSOR SENSITIVITY 89
POWER SUPPLY CHECKS 90

Komentarze do niniejszej Instrukcji

Brak uwag

Max Systems LabelMax XS Instrukcja Obsługi Strona 19

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Drukarki etykiet Max Systems LabelMax XS